Overview
The Massey Ferguson 8816 and 8824 Planter Workshop Service Manual provides technical information for servicing, adjusting and troubleshooting these Massey Ferguson agricultural planters. The publication also identifies an 8824-70 cm configuration alongside 30-inch-row references. Its chapters cover row units, ground and hydraulic seed drives, central-fill and seed-meter air systems, hydraulic circuits, electrical wiring, frame and marker assemblies, fertilizer equipment, and GTA consoles and monitors.
Workshop subjects include seed disc and closing-wheel adjustments, pneumatic down pressure, point-row clutches, seed population and rate tables, planter lift and folding hydraulics, PTO-driven pumps, hydraulic motors, seed-sensor diagnostics, and ISOBUS controller setup. Separate references address the NGP-6055 single-piston and NGP-8055-DR double-piston fertilizer pumps, 16- and 24-row assemblies, CE/non-CE equipment, and ground-drive versus hydraulic-drive planter control.
Safety: The source includes precautions for operation, agricultural chemicals, transporting and servicing the planter. Consult the relevant safety information before working on folding assemblies, hydraulic components, chemical equipment or supported machine sections.
Notice: The bookmarks include distinct 8816, 8824 and 8824-70 cm specifications, plus different row-count, hitch, electrical, hydraulic and drive configurations. Use the instructions and diagrams corresponding to the actual planter and installed equipment.
Table of Contents
Massey Ferguson 8816, 8824 Manual
-
01. General Information, Safety and Specifications
- Machine Identification and Serial Number Plate Location
- Safety Instructions, Signs and Operator Precautions
- Agricultural Chemical Handling, Transport and Servicing Safety
- 8816 and 8824 — 30-Inch Row Configuration Specifications
- 8824 — 70 cm Row Configuration Specifications
- Frame, Tyre, Wheel and Optional Marker Specifications
- Row Unit, Air System and Hydraulic Specifications
- Shear Pins, Electronic Seed Drive, Monitor and Fuse References
- Approximate Shipping Weights
- Recommended Tractor Horsepower and Fertilizer Opener Requirements
- Tractor Wheel Tread, PTO, Tyre, Ballast and Electrical Preparation
- Three-Point Hitch and Drawbar Hitch Connections
- Planter Hydraulic Lines and PTO Pump Fluid
- Seed Meter Blower and Meter Drive Hose Connections
- Tractor Remote Hydraulic Valve Flow Adjustment
- Control Box Switches and Operating Notes
- Planter Folding, Unfolding and Marker Operation
- Marker Sequence Valve, Position Switch and Shear Bolts
- Seed Recommendations and Initial Air Pressure Settings
- Liquid Fertilizer Application Rate and Piston Pump Drive Charts
- Single- and Double-Disc Fertilizer Opener Adjustments
- CE and Non-CE Chemical Application Rate Charts
- ISOBUS Planter Controller, Implement Switch and Radar Sensor
- Hydraulic Circuit Priming and Installation Instructions
- Standard, Metric and Special Bolt Tightening Torques
-
02. Row Unit and Seed Meter
- Gauge Wheel Clearance, Wheel Arm Endplay and Mounting
- Gauge Wheel Disassembly and Reassembly
- Disc Opener Blade Replacement and Adjustment
- Scraper Bearings, Rotary Scraper Tension and Flat Scrapers
- Seed Tube Sensor Cleaning and Tube Guards
- Lower Row Unit and Depth Gauge Servicing
- Planting Depth Adjustment, Calibration and Field Checks
- Single Closing Wheel Removal, Assembly and Down Pressure
- Dual Rubber and Cast Closing Wheels, Spacing and Offset
- Closing Wheel Centring and Row Unit Linkage Maintenance
- Standard- and Heavy-Duty Down-Pressure Springs
- Pneumatic Down Pressure — Air Compressor, Filter and Air Springs
- Seed Meter Drive Chains, Sprockets and Idler Pulleys
- Insecticide Delivery Funnels, Diffuser and In-Furrow Application
- Chemical Attachment Hoppers and Meter Cleaning
- Seed Hopper Covers and Seed Removal
- Seed Meter Removal, Installation and Clutch Alignment
- Seed Disc Installation, Clearance and Seed Gate Adjustment
- Metering Drive Shaft and Bearing Replacement
- Tickler Brush and Air Cut-Off Brush Servicing
-
03. Drive Transmission
- Roller Chain Lubrication, Elongation and Sprocket Alignment
- Ground Drive Wheel Arm and Roller Chains
- Front Sprocket Assembly and Upper Wheel Arm Tightener
- Torsion Spring and Lower Rear Sprocket Assembly
- High/Low Idler Position Change
- Ground Drive Wheel and Tyre Assembly
- Idler Sprockets and Pulleys
- Ground Drive Shaft and Wheel Arm Chain
- Drive Bearing Support Chain and Hex-Bore Bearings
- Point-Row Clutch Removal, Overhaul and Installation
- Drive Bearing Support Sprocket Assembly
- Hydraulic Drive — Roller Chain and Idler Pulley
- Hydraulic Drive — 16-Tooth and 40-Tooth Sprockets
- Drive Shaft Centre and Bearing Assembly Sprocket
- Inner Wing Drive Shafts — 16-Row and 24-Row Versions
- Outer Wing Drive Shafts — 16-Row and 24-Row Versions
- Ground Drive Seed Rate Transmission and Planting Rates (Non-CE)
- Ground Drive Seed Rate Charts and Metric Planting Rates (CE)
- Seed Disc Identification — 30, 50, 60 and 120 Seeds per Disc
- Bean, Snap Bean and Peanut Seed Disc References
- Seed Population per Acre and per Hectare
- Row Width, Disc Cell and Seed Population Conversion Factors
-
04. Central Fill and Seed Meter Air Systems
- Central Fill Air Pressure and Pressure Gauge
- Central Fill Blower Removal, Inspection and Reassembly
- New or Repaired Central Fill Blower Start-Up
- Central Fill Plenum Operation, Cleaning and Seed Delivery
- Plenum Distribution — 16-Row and 24-Row Wings and Centre
- Seed Meter Covers Removal and Installation
- Seed Meter Air Pressure and Gauge Calibration
- Seed Meter Blower Removal and Overhaul
- Seed Meter Air Tubes and Cleaning
- Air Tube Routing — 16-Row and 24-Row Wings and Centre
-
05. Hydraulic System
- Hydraulic Seed Drive and Ground Drive Circuit Schematics
- Marker, Fold, Lift and Central Fill Blower Circuits
- Raising and Lowering the Planter and Wing Wheels
- Hydraulic Fluid Level, Replacement, Filters and Hoses
- PTO Hydraulic Pump Specifications and Operation
- PTO Pump Removal, Inspection and Reassembly
- Row Unit Drive Motor Operation and Overhaul
- Central Fill Blower Motor Repair and Test Run
- Seed Meter Blower Motor Servicing
- Hydraulic Oil Cooler Removal and Cleaning
- Wing Fold and Latch Hydraulic Cylinders
- Marker Hydraulic Cylinders — 8816 and 8824 Variants
- Master, Slave and Lift-Assist Cylinder Specifications
- Wing and Centre Lift Cylinder Servicing
- Drawbar Hitch Hydraulic Cylinder Overhaul
- Marker/Fold Valve Block and Solenoid Servicing
- Marker Sequencing Valves — 8816 and 8824 Variants
- Lift Valve Block and Solenoid Servicing
- Flow Divider Valve and Flow Control Valve
- PWM Motor Control Valve
- Blower Control Valve
-
06. Electrical System and Wiring
- Transport Lights and Harnesses — Non-CE Versions
- 7-Pin SAE Light Connector and Tail Light Module Switch
- Optional Tow Hitch Harness
- Transport Lights and Harnesses — 8824-70 cm CE Version
- Marker, Fold and Lift Wiring Schematics
- Control Box Voltage Testing and Lift Limit Switch
- Marker Position Switch Adjustment and Solenoid Coil Testing
- Seed Sensor and Module Harnesses
- ISO Hydraulic Drive, Hitch and Monitor Harnesses
- ISO Two-Channel Actuator and Bridge Module Harnesses
- ISOBUS Planter Controller and PWM Channel Coil
- Shaft Speed Sensor Testing and Optional Lift Switch
- ISO Ground Drive and Magnetic Speed Sensor
- Non-ISO Harness and Terminator Adapter
- Bridge and Interface Modules — Diagnostic Indicator Lamps
- Seed Sensors — Removal, Cleaning and Testing
- Seed Monitor Tests and Wiring Diagrams
- Drive Shaft Clutch Harness and Extension
- Clutch Solenoid and Clutch Control Box
-
07. Frame, Hitch and Marker Assemblies
- Lift Wheels, Tyres and Wheel Lift Arms
- Wing Braces and Inner/Outer Wing Mountings
- Tongue, Inner Hitch and Roller Tube
- Inner Hitch Roller, Slide Buttons and Slide Blocks
- Tongue Latch and Hitch Pivot
- Two-Point and Drawbar Hitch Servicing
- Optional Rear Hitch and Tow Hitch Clevis
- Lower Marker Arm — 16-Row and 24-Row Versions
- Upper Marker Arm and Telescoping Rod Roller Link
- Marker Arm Length Adjustment
- Marker Gauge Wheels — 16-Row and 24-Row Versions
- Marker Disc Blade Assembly and Adjustment
- Central Fill System Hopper Removal and Installation
- Central Fill Ladder, Platform and Cradle Servicing
- 08. Troubleshooting
-
09. Fertilizer System
- NGP-6055 Single-Piston Fertilizer Pump
- Piston Pump Check Valves, Piston and Rod Packing
- Piston Pump Inboard/Outboard and Internal Crankcase Servicing
- NGP-8055-DR Double-Piston Fertilizer Pump
- Fertilizer Drive Roller Chains and Drive Wheel
- Fertilizer Flow Distribution and Flow Divider
- Fertilizer Manifold and Check Valves
- Ball Valves — 1.5-Inch and 2-Inch Variants
- Fertilizer Strainer and Full-Port Ball Valve
- Double-Disc Fertilizer Opener Servicing
- Single-Disc Fertilizer Opener Servicing
- Fertilizer Disc Opener Mounting — 16-Row and 24-Row
-
10. Consoles and Monitors
- GTA Console I and GTA Console II Schematics
- ISOBUS Planter System and Console Display Functions
- Work Screen, Seed Monitor and Key Functions
- Material Selection, Ground Speed and Alarms
- Hydraulic Drive Planter Setup and Seed Configuration
- Ground Drive Planter Setup and Monitor-Only Operation
- Hydraulic Drive Seeding Rate and Application Map Control
- Accumulators, Operating Time and Distance
- Configuration Import and Export
- Material and Channel Setup — Hydraulic and Ground Drive
- Channel Calibration and GPS Implement Setup
- Seed Monitor Population and Row Failure Settings
- Row Status, Row Width and Implement Width Setup
- Ground Speed Source, Constant and Calibration
- Module Address, Automatic and Bridge Configuration
- Hopper and Accessory Sensor Configuration
- Work Screen Graphs and Population Data Items
- Diagnostic Screen and Bridge Diagnostics
- Remote, Continuous and Five-Revolution Tests
- Alarm History and Alarm Chart
- GTA Console I and II Dual Hydraulic Drive Start-Up Guides
- GTA Console Software Upgrade Instructions
Row-Count, Seed-Drive and GTA Console Service References
The transmission section distinguishes ground wheel drive and hydraulic seed drive, with separate inner- and outer-wing drive shafts for 16-row and 24-row machines. The air-system chapter likewise separates wing and centre delivery routing for central-fill and seed-meter systems. The 8824-70 cm configuration also has specific CE transport-light references.
The GTA console chapter provides different setup and operating instructions for hydraulic-drive and ground-drive planters, including seed rate control, channel calibration, ground speed configuration, seed monitoring and diagnostics. Fertilizer service chapters distinguish the NGP-6055 single-piston pump from the NGP-8055-DR double-piston pump; select procedures by the installed pump, drive and controller configuration.
Reviews
There are no reviews yet.