Overview
The Massey Ferguson 4607M, 4609M, 4610M and 4610M HC Tractor Workshop Service Repair Manual provides technical information for maintaining, diagnosing and repairing these Massey Ferguson 4600M Series agricultural tractors. The documentation covers general tractor information, engine fuel and exhaust systems, drivetrain components, chassis, cab, axles, braking systems, electrical equipment, hydraulics and hydrostatic steering.
Workshop coverage includes PowerShuttle transmission servicing, clutch pack disassembly, input gears, main and range-change gear mechanisms, creeper gears, four-wheel-drive components and independent power take-off systems. Detailed electrical sections provide wiring diagrams for cab and platform tractors, controller configurations, solenoid valves, clutch and linkage calibrations, diagnostic fault codes and instrument panel servicing. Hydrostatic steering procedures include Orbitrol control unit disassembly, gerotor inspection, reassembly and troubleshooting.
Caution: During air-conditioning repairs, close refrigerant circuit openings after disassembly to reduce moisture entry and protect the receiver-dryer desiccant. Follow the applicable safety and service instructions before opening the system.
Table of Contents
Massey Ferguson 4607M, 4609M, 4610M, 4610M HC Manual
- 01. General Information
- 02. Engine, Fuel and Exhaust
-
03. Drive Train System
- 3.1 Transmission
- 3.1.1 Separation Locations
- 3.1.2 Separate the Engine from the Front Transmission
- 3.1.3 Separate the Front and Middle Transmission Housings
- 3.1.4 Separate the Middle and Rear Transmission Housings
- 3.1.5 Separate the Rear Axle Housing from the Rear Housing
- 3.1.6 Attaching the Rear Axle to the Rear Transmission Case
- 3.1.7 Power Shuttle Transmission
- 3.1.8 Power Train
- 3.1.9 Gear Ratios
- 3.1.10 Shuttle Clutch
- 3.1.11 Assembly Precautions for Power Shuttle
- 3.2 Clutch Pack
- 3.2.1 Reverse Clutch Pack Components
- 3.2.2 Disassembling the Reverse Clutch
- 3.3 Input Gears
- 3.3.1 Removing the Input Gear
- 3.3.2 Disassembling the Input Gear
- 3.3.3 Assembling the Input Gears
- 3.3.4 Disassembling the Rear and Middle Transmission Housings
- 3.3.5 Input Gears
- 3.4 Transmission Main Change Gears
- 3.4.1 Assembly Precautions for the Main Gear System
- 3.4.2 Main Shift Lever
- 3.4.3 Assembly Precautions for the Main Shift Lever
- 3.4.4 Disassembling the High-Low Gear
- 3.5 Creep Gear
- 3.5.1 Creeper Gear Components
- 3.5.2 Disassembling the Creeper Gear
- 3.5.3 Assembling the Creeper Gear
- 3.6 Transmission Range Change Gears
- 3.6.1 Range Gear Shift
- 3.6.2 Installing the Range Gear Shift
- 3.6.3 Range Shift Linkage
- 3.6.4 Independent Power Take-Off
- 3.6.5 Power Take-Off Clutch
- 3.6.6 Power Take-Off Assembly Precautions
- 3.6.7 Four-Wheel Drive Gears, If Equipped
- 3.6.8 Four-Wheel Drive Assembly, If Equipped
- 3.6.9 Four-Wheel Drive Gear System
- 3.6.10 Two-Wheel Drive Gear System
- 3.6.11 Power Take-Off Speed
- 3.6.12 Power Take-Off Lever
- 3.6.13 Power Take-Off Link Check System
- 04. Chassis
- 05. Cab
- 06. Axles
- 07. Brake System
-
08. Electrical System
- 8.1 Wire Color Chart
- 8.2 Wiring Diagrams
- 8.2.1 Wiring Diagram Abbreviations
- 8.2.2 Engine – Cab Tractor – 4607M (North America)
- 8.2.3 Engine – Platform Tractor – 4607M (North America)
- 8.2.4 Engine – Cab Tractor – 4609M and 4610M (North America)
- 8.2.5 Engine – Platform Tractor – 4609M and 4610M (North America)
- 8.2.6 Engine – Cab Tractor (Australia)
- 8.2.7 Engine – Platform Tractor (Australia)
- 8.2.8 Lighting – Cab Tractor (North America)
- 8.2.9 Lighting – Platform Tractor (North America)
- 8.2.10 Lighting – Cab Tractor (Australia)
- 8.2.11 Lighting – Platform Tractor (Australia)
- 8.2.12 Chassis, Fuse Block and Relay – Cab Tractor (North America)
- 8.2.13 Chassis, Fuse Block and Relay – Platform Tractor (North America)
- 8.2.14 Chassis, Fuse Block and Relay – Cab Tractor (Australia)
- 8.2.15 Chassis, Fuse Block and Relay – Platform Tractor (Australia)
- 8.2.16 Controller – Cab Tractor (North America)
- 8.2.17 Controller – Cab Tractor (Australia)
- 8.2.18 Controller – Cab Tractor (Effective 2017 Model Year Changes)
- 8.2.19 Controller – Platform Tractor (North America)
- 8.2.20 Controller – Platform Tractor (Australia)
- 8.2.21 Controller – Platform Tractor (Effective 2017 Model Year Changes)
- 8.2.22 Cab Electrical Diagram (North America)
- 8.2.23 Cab Electrical Diagram (Australia)
- 8.3 Instruments and Controls
- 8.3.1 Removing the Console
- 8.3.2 Panel Switch
- 8.3.3 Removing the Instrument Panel
- 8.3.4 Installing the Instrument Panel
- 8.3.5 Instrument Panel Switch Location Diagram
- 8.3.6 Cab Switch Location Diagram
- 8.3.7 Lever Guide Switch Location Diagram
- 8.3.8 Main Fuse Box – Platform Tractor
- 8.3.9 Main Fuse Box – Cab Tractor
- 8.4 Valves
- 8.4.1 Power Shuttle Valve
- 8.4.2 Power Take-Off Valve
- 8.4.3 Solenoid Valves
- 8.5 Position of the Main Electrical Parts
- 8.5.1 Range Change Lever Position Sensor
- 8.5.2 Air Conditioner Controller Panel
- 8.5.3 Air Conditioner Control Unit
- 8.5.4 Cab Harness Connection
- 8.5.5 Engine Harness Connection
- 8.5.6 Headlamp Connection
- 8.5.7 Horn Connection
- 8.5.8 Starter Connection
- 8.6 Calibration and Initial Adjustment
- 8.6.1 Configuring the Controller
- 8.6.2 Calibrating the Power Shuttle Sensitivity Dial
- 8.6.3 Calibrating the Three-Point Linkage
- 8.6.4 Lift Arm and Draft Sensor
- 8.6.5 Location of Instruments and Controls
- 8.6.6 Instrument Panel Components
- 8.6.7 Calibrating the Clutch Pedal Switch and Sensor
- 8.6.8 Clutch Pedal Sensor
- 8.6.9 Clutch Pedal Switch
- 8.6.10 Calibrating the Clutch Initial Time
- 8.6.11 Parking Lever Switch, If Equipped
- 8.6.12 Brake Pedal Switch
- 8.6.13 Instrument Panel
- 8.6.14 Stored Engine Speed Switch
- 8.6.15 Calibrating the Throttle Lever and Accelerator Pedal
- 8.6.16 Power Take-Off Shaft Safety Switch
- 8.7 Electrical and Hydraulic Control System
- 8.8 Main Clutch System
- 8.9 Electronic Diagnostic Tool
- 8.9.1 Engine Service Tool Software License
- 8.9.2 Connecting the Electronic Diagnostic Tool
- 8.10 Fault Code Tree
- 8.11 Diagnostic Codes
- 8.11.1 SPN 1001 FMI 1
- 8.11.2 SPN 1001 FMI 2
- 8.11.3 SPN 1001 FMI 3
- 8.11.4 SPN 1002 FMI 1
- 8.11.5 SPN 1002 FMI 2
- 8.11.6 SPN 1002 FMI 3
- 8.11.7 SPN 1004 FMI 1
- 8.11.8 SPN 1004 FMI 2
- 8.11.9 SPN 1004 FMI 3
- 8.11.10 SPN 3053 FMI 1
- 8.11.11 SPN 3053 FMI 2
- 8.11.12 SPN 3053 FMI 3
- 8.11.13 SPN 3055 FMI 1
- 8.11.14 SPN 3055 FMI 2
- 8.11.15 SPN 3055 FMI 3
- 8.11.16 SPN 3057 FMI 1
- 8.11.17 SPN 3057 FMI 2
- 8.11.18 SPN 3151 FMI 6
- 8.11.19 SPN 3151 FMI 7
- 8.11.20 SPN 3151 FMI 8
- 8.11.21 SPN 3151 FMI 9
- 8.11.22 SPN 3152 FMI 4
- 8.11.23 SPN 3154 FMI 4
- 8.11.24 SPN 3156 FMI 8
- 8.11.25 SPN 3156 FMI 09
- 8.11.26 SPN 3351 FMI 3
- 8.11.27 SPN 3351 FMI 21
- 8.11.28 SPN 3351 FMI 22
- 8.11.29 SPN 3352 FMI 3
- 8.11.30 SPN 3352 FMI 21
- 8.11.31 SPN 3352 FMI 22
- 8.11.32 SPN 3357 FMI 3
- 8.11.33 SPN 3357 FMI 21
- 8.11.34 SPN 3357 FMI 22
- 8.11.35 SPN 3358 FMI 3
- 8.11.36 SPN 3358 FMI 21
- 8.11.37 SPN 3358 FMI 22
- 8.11.38 SPN 9502 FMI 0
- 09. Hydraulic System
-
10. Steering System
- 10.1 Hydrostatic Steering
- 10.1.1 Steering Description
- 10.1.2 Major Components
- 10.1.3 Orbit Roll Disassembly
- 10.1.4 Disassembling the Gerotor Side
- 10.1.5 Disassembling the Control Side
- 10.1.6 Inspecting the Orbit Roll
- 10.1.7 Assembling the Control Side
- 10.1.8 Assembling the Gerotor Side
- 10.1.9 Steering Control Unit Specifications
- 10.1.10 Troubleshooting
Air-Conditioning Service Notes
The supplied air-conditioning service note explains the receiver-dryer’s role in controlling refrigerant-circuit moisture and the importance of protecting its desiccant during repairs. Together with the manual’s drivetrain, wiring, calibration and steering procedures, these references support servicing the applicable Massey Ferguson 4607M, 4609M and 4610M tractor configurations.
Reviews
There are no reviews yet.