Overview
The Massey Ferguson 7619, 7620, 7622, 7624 and 7626 Tractor Workshop Service Manual provides technical information for servicing, diagnosing and repairing these MF 7600 Series tractors. The documentation covers model specifications, operating systems, fault codes, workshop procedures, component diagrams, adjustments and calibration references.
Its detailed sections cover Sisu Tier 4i diesel engines and e3 SCR technology, Dyna-6 and Dyna-VT transmission systems, GBA15 and GBA25 gearboxes, HA130/160, GPA20 and GPA40 rear axle arrangements, PTO mechanisms, Dana front axles, hydraulic circuits and electrical equipment. Other material addresses electronic control components, wiring harnesses, air conditioning and cab suspension.
Safety: The engine material contains safety instructions for handling AdBlue/DEF, and the cab section includes air conditioning service safety instructions. Follow the applicable safety precautions before servicing pressurised systems, braking components or refrigerant circuits.
Notice: The general MF 7600 specifications include additional models and equipment variants beyond the five models in this listing. Several hydraulic subsection pages are marked intentionally blank and direct readers to Chapter 1 diagrams. Confirm the tractor model, transmission and installed equipment before applying configuration-specific service information.
Table of Contents
Massey Ferguson 7619, 7620, 7622, 7624, 7626 Manual
-
1. Introduction
- 1A10 – MF 7600 – General
- 1A11 – MF 7600 – Error codes
- 1A12 – MF 7600 – Fuse box, electrical diagrams, harnesses, hydraulics diagrams and pneumatic diagrams
- 1A16 – MF 7600 – Adjustments, bleeding and calibrations
- 2. Separation of Assemblies
-
3. Engine
- 3A11 – Sisu Tier 4i engine – Error codes
- 3A12 – Sisu Tier 4i engine – Electrical and hydraulics diagrams
- 3A13 – Sisu Tier 4i engine – Layout of components
- 3A14 – Sisu Tier 4i engine – Tests and diagnostics
- 3A16 – Sisu Tier 4i engine – Adjustments, bleeding and calibrations
- 3A17 – Sisu Tier 4i engine – Disassembly and reassembly
- 3B10 – e3 SCR Technology engine – General
- 3B12 – e3 SCR Technology engine – Electrical and hydraulics diagrams
- 3B13 – e3 SCR Technology engine – Layout of components
- 3B17 – e3 SCR Technology engine – Disassembly and reassembly
- 3B18 – e3 SCR Technology engine – Service tools
- 4. Clutch
-
5. Gearbox
- 5A10 – ML130/ML160 – General
- 5A11 – ML130/ML160 – Error codes
- 5A12 – ML130/ML160 – Electrical and hydraulics diagrams
- 5A14 – ML130/ML160 – Tests and diagnostics
- 5A16 – ML130/ML160 – Adjustments, bleeding and calibrations
- 5A17 – ML130/ML160 – Disassembly and reassembly
- 5A18 – ML130/ML160 – Service tools
- 5B10 – GBA15 – General
- 5B13 – GBA15 – Layout of components
- 5B17 – GBA15 – Disassembly/reassembly
- 5B20 – GBA15/PowerShuttle – General
- 5B23 – GBA15/PowerShuttle – Layout of components
- 5B27 – GBA15/PowerShuttle – Disassembly/reassembly
- 5B28 – GBA15/PowerShuttle – Service tools
- 5B30 – GBA15/Powershift module – General
- 5B33 – GBA15/Powershift module – Layout of components
- 5B37 – GBA15/Powershift module – Disassembly/reassembly
- 5B38 – GBA15/Powershift module – Service tools
- 5B40 – GBA15/Robotic mechanical gearbox – General
- 5B43 – GBA15/Robotic mechanical gearbox – Layout of components
- 5B47 – GBA15/Robotic mechanical gearbox – Disassembly/reassembly
- 5B48 – GBA15/Robotic mechanical gearbox – Service tools
- 5B50 – GBA15/Creeper gears – General
- 5B53 – GBA15/Creeper gears – Layout of components
- 5B57 – GBA15/Creeper gears – Disassembly/reassembly
- 5C10 – GBA25 – General
- 5C11 – GBA25 – Error codes
- 5C13 – GBA25 – Layout of components
- 5C14 – GBA25 – Tests and diagnostics
- 5C15 – GBA25 – Programming and setting parameters
- 5C16 – GBA25 – Adjustments, bleeding and calibrations
- 5C17 – GBA25 – Disassembly and reassembly
- 5C20 – GBA25/PowerShuttle – General
- 5C23 – GBA25/PowerShuttle – Layout of components
- 5C27 – GBA25/PowerShuttle – Disassembly and reassembly
- 5C28 – GBA25/PowerShuttle – Service tools
- 5C30 – GBA25/Powershift module – General
- 5C33 – GBA25/Powershift module – Layout of components
- 5C37 – GBA25/Powershift module – Disassembly and reassembly
- 5C38 – GBA25/Powershift module – Service tools
- 5C40 – GBA25/Robotic mechanical gearbox – General
- 5C43 – GBA25/Robotic mechanical gearbox – Layout of components
- 5C47 – GBA25/Robotic mechanical gearbox – Disassembly and reassembly
- 5C48 – GBA25/Robotic mechanical gearbox – Service tools
- 5C50 – GBA25/Creeper gears – General
- 5C53 – GBA25/Creeper gears – Layout of components
- 5C57 – GBA25/Creeper gears – Disassembly and reassembly
- 5C60 – GBA25/Super creeper gears – General
- 5C63 – GBA25/Super creeper gears – Layout of components
- 5C67 – GBA25/Super creeper gears – Disassembly and reassembly
-
6. Rear Axle
- 6A13 – HA130/160/Final drives – Layout of components
- 6A17 – HA130/160/Final drives – Disassembly and reassembly
- 6A21 – HA130/160/Differential – Error codes
- 6A22 – HA130/160/Differential – Electrical and hydraulics diagrams
- 6A23 – HA130/160/Differential – Layout of components
- 6A26 – HA130/160/Differential – Adjustments, bleeding and calibrations
- 6A27 – HA130/160/Differential – Disassembly and reassembly
- 6A31 – HA130/160/Tractor braking – Error codes
- 6A32 – HA130/160/Tractor braking – Electrical and hydraulics diagrams
- 6A33 – HA130/160/Tractor braking – Layout of components
- 6A37 – HA130/160/Tractor braking – Disassembly and reassembly
- 6A40 – HA130/160/ParkLock – General
- 6A41 – HA130/160/ParkLock – Error codes
- 6A42 – HA130/160/ParkLock – Electrical and hydraulics diagrams
- 6A43 – HA130/160/ParkLock – Layout of components
- 6A46 – HA130/160/ParkLock – Adjustments, bleeding and calibrations
- 6A51 – HA130/160/Hydraulic trailer braking – Error codes
- 6A52 – HA130/160/Hydraulic trailer braking – Electrical and hydraulics diagrams
- 6A60 – HA130/160/Pneumatic trailer braking – General
- 6A62 – HA130/160/Pneumatic trailer braking – Electrical and hydraulics diagrams
- 6A63 – HA130/160/Pneumatic trailer braking – Layout of components
- 6A64 – HA130/160/Pneumatic trailer braking – Tests and diagnostics
- 6A66 – HA130/160/Pneumatic trailer braking – Adjustments, bleeding and calibrations
- 6A67 – HA130/160/Pneumatic trailer braking – Disassembly and reassembly
- 6B10 – GPA40/Rear axle – General
- 6B13 – GPA40/Rear axle – Location of components
- 6B17 – GPA40/Rear axle – Disassembly and reassembly
- 6B20 – GPA40/Trumpet housings – General
- 6B23 – GPA40/Trumpet housings – Layout of components
- 6B27 – GPA40/Trumpet housings – Disassembly and reassembly
- 6B28 – GPA40/Trumpet housings – Service tools
- 6B30 – GPA40/Differential – General
- 6B33 – GPA40/Differential – Layout of components
- 6B37 – GPA40/Differential – Disassembly and reassembly
- 6B38 – GPA40/Differential – Service tools
- 6B40 – GPA40/Tractor braking – General
- 6B43 – GPA40/Tractor braking – Layout of components
- 6B46 – GPA40/Tractor braking – Adjustments, bleeding and calibrations
- 6B47 – GPA40/Tractor braking – Disassembly and reassembly
- 6B48 – GPA40/Tractor braking – Service tools
- 6B50 – GPA40/ParkLock – General
- 6B53 – GPA40/ParkLock – Layout of components
- 6B57 – GPA40/ParkLock – Disassembly and reassembly
- 6B60 – GPA40/Hitch/Linkage – General
- 6B63 – GPA40/Hitch/Linkage – Layout of components
- 6B67 – GPA40/Hitch/Linkage – Disassembly and reassembly
- 6B70 – GPA40/Pneumatic trailer braking – General
- 6B72 – GPA40/Pneumatic trailer braking – Electrical and hydraulics diagrams
- 6B73 – GPA40/Pneumatic trailer braking – Layout of components
- 6B74 – GPA40/Pneumatic trailer braking – Tests and diagnostics
- 6B76 – GPA40/Pneumatic trailer braking – Adjustments, bleeding and calibrations
- 6B77 – GPA40/Pneumatic trailer braking – Disassembly and reassembly
- 6B80 – GPA40/Auto-hitch – General
- 6B83 – GPA40/Auto-hitch – Layout of components
- 6B86 – GPA40/Auto-hitch – Adjustments, bleeding and calibrations
- 6B87 – GPA40/Auto-hitch – Disassembly and reassembly
- 6B90 – GPA40/Rear wheels/hubs – General
- 6B97 – GPA40/Rear wheels/hubs – Disassembly and reassembly
- 6C10 – GPA20 – General
- 6C13 – GPA20 – Layout of components
- 6C20 – GPA20/Trumpet housings – General
- 6C23 – GPA20/Trumpet housings – Layout of components
- 6C27 – GPA20/Trumpet housings – Disassembly and reassembly
- 6C28 – GPA20/Trumpet housings – Service tools
- 6C30 – GPA20/Differential – General
- 6C33 – GPA20/Differential – Layout of components
- 6C37 – GPA20/Differential – Disassembly and reassembly
- 6C38 – GPA20/Differential – Service tools
- 6C40 – GPA20/Tractor braking – General
- 6C43 – GPA20/Tractor braking – Layout of components
- 6B46 – GPA40/Tractor braking – Adjustments, bleeding and calibrations
- 6C47 – GPA20/Tractor braking – Disassembly and reassembly
- 6C60 – GPA20/Hydraulic trailer braking – General
- 6C63 – GPA20/Hydraulic trailer braking – Layout of components
- 6C67 – GPA20/Hydraulic trailer braking – Disassembly and reassembly
- 6C70 – GPA20/Pneumatic trailer braking – General
- 6C72 – GPA40/Pneumatic trailer braking – Electrical and hydraulics diagrams
- 6C73 – GPA20/Pneumatic trailer braking – Layout of components
- 6C74 – GPA20/Pneumatic trailer braking – Tests and diagnostics
- 6C76 – GPA20/Pneumatic trailer braking – Adjustments, bleeding and calibrations
- 6C77 – GPA20/Pneumatic trailer braking – Disassembly and reassembly
- 6C80 – GPA20/Hitch/Linkage – General
- 6C83 – GPA20/Hitch/Linkage – Layout of components
- 6C86 – GPA20/Hitch/Linkage – Adjustments, bleeding and calibrations
- 6C87 – GPA20/Hitch/Linkage – Disassembly and reassembly
- 6C90 – GPA20/Auto-hitch – General
- 6C96 – GPA20/Auto-hitch – Adjustments, bleeding and calibrations
- 6D80 – GPA20 +/Hitch/Increased capacity linkage – General
- 6D83 – GPA20 +/Hitch/Increased capacity linkage – Layout of components
- 6D86 – GPA20 +/Hitch/Increased capacity linkage – Adjustments, bleeding and calibrations
- 6D87 – GPA20 +/Hitch/Increased capacity linkage – Disassembly and reassembly
- 6D88 – GPA20 +/Hitch/Increased capacity linkage – Service tools
-
7. Power Take-Off
- 7A11 – HA130/160/Power take-off – Error codes
- 7A12 – HA130/160/Power take-off – Electrical and hydraulics diagrams
- 7A13 – HA130/160/Power take-off – Layout of components
- 7A16 – HA130/160/Power take-off – Adjustments, bleeding and calibrations
- 7A17 – HA130/160/Power take-off – Disassembly and reassembly
- 7B10 – GPA40 – General
- 7B13 – GPA40 – Layout of components
- 7B17 – GPA40 – Disassembly/reassembly
- 7B20 – GPA40/Intermediate shaft and driving gears – General
- 7B23 – GPA40/Intermediate shaft and driving gears – Layout of components
- 7B27 – GPA40/Intermediate shaft and driving gears – Disassembly/reassembly
- 7B30 – GPA40/Output shaft and brake – General
- 7B33 – GPA40/Output shaft and brake – Layout of components
- 7B37 – GPA40/Output shaft and brake – Disassembly/reassembly
- 7B38 – GPA40/Output shaft and brake – Service tools
- 7B40 – GPA40/GSPTO – General
- 7B43 – GPA40/GSPTO – Layout of components
- 7B47 – GPA40/GSPTO – Disassembly/reassembly
- 7B50 – GPA40/Clutch – General
- 7B53 – GPA40/Clutch – Layout of components
- 7B57 – GPA40/Clutch – Disassembly/reassembly
- 7B58 – GPA40/Clutch – Service tools
- 7C10 – GPA20 – General
- 7C20 – GPA20/Intermediate shaft/Driving gear/PTO brake – General
- 7C23 – GPA20/Intermediate shaft/Driving gear/PTO brake – Layout of components
- 7C27 – GPA20/Intermediate shaft/Driving gear/PTO brake – Disassembly and reassembly
- 7C40 – GPA20/GSPTO – General
- 7C43 – GPA20/GSPTO – Layout of components
- 7C47 – GPA20/GSPTO – Disassembly and reassembly
- 7C50 – GPA20/Removable PTO shaft – General
- 7C53 – GPA20/Removable PTO shaft – Layout of components
- 7C57 – GPA20/Removable PTO shaft – Disassembly and reassembly
- 7C60 – GPA20/Shiftable PTO shaft – General
- 7C63 – GPA20/Shiftable PTO shaft – Layout of components
- 7C67 – GPA20/Shiftable PTO shaft – Disassembly and reassembly
- 7C70 – GPA20/Clutch – General
- 7C73 – GPA20/Clutch – Layout of components
- 7C77 – GPA20/Clutch – Disassembly and reassembly
- 7C78 – GPA20/Clutch – Service tools
- 7D10 – GPA20/PTO electrohydraulic controls – General
- 7D17 – GPA20/PTO electrohydraulic controls – Disassembly and reassembly
- 7E10 – Zuidberg front power take-off – General
- 7E13 – Zuidberg front power take-off – Layout of components
- 7E14 – Zuidberg front power take-off – Tests and diagnostics
- 7E16 – Zuidberg front power take-off – Adjustments, bleeding and calibrations
- 7E17 – Zuidberg front power take-off – Disassembly and reassembly
-
8. Front Axle
- 8A10 – DANA – General
- 8A11 – DANA – Error codes
- 8A12 – DANA – Electrical and hydraulics diagrams
- 8A16 – DANA – Adjustments, bleeding and calibrations
- 8A17 – DANA – Disassembly and reassembly
- 8B10 – HA130/160 4WD clutch – General
- 8B12 – HA130/160/4WD clutch – Electrical and hydraulics diagrams
- 8B16 – HA130/160/4WD clutch – Adjustments, bleeding and calibrations
- 8B17 – HA130/160/4WD clutch – Disassembly and reassembly
- 8B20 – HA130/160/Universal joint shaft brake – General
- 8B27 – HA130/160/Universal joint shaft brake – Disassembly and reassembly
- 8C10 – GPA40/4WD clutch – General
- 8C13 – GPA40/4WD clutch – Layout of components
- 8C17 – GPA40/4WD clutch – Disassembly and reassembly
- 8D10 – Steering unit/Closed Centre – General
- 8D12 – Steering unit/Closed Centre – Electrical and hydraulics diagrams
- 8D13 – Steering unit/Closed Centre – Layout of components
- 8D17 – Steering unit/Closed Centre – Disassembly and reassembly
- 8D20 – Steering unit/Open Centre – General
- 8D22 – Steering unit/Open Centre – Electrical and hydraulics diagrams
- 8D23 – Steering unit/Open Centre – Layout of components
- 8D27 – Steering unit/Open Centre – Disassembly and reassembly
- 8E17 – Steering rams – Disassembly and reassembly
-
9. Hydraulics
- 9A10 – HA130/160/LS hydraulic system – General
- 9A12 – HA130/160/LS hydraulic system – Electrical and hydraulics diagrams
- 9A13 – HA130/160/LS hydraulic system – Layout of components
- 9A14 – HA130/160/LS hydraulic system – Tests and diagnostics
- 9A17 – HA130/160/LS hydraulic system – Disassembly and reassembly
- 9A18 – HA130/160/LS hydraulic system – Service tools
- 9A20 – HA130/160/LS hydraulic system/Hydraulic pumps – General
- 9A22 – HA130/160/LS hydraulic system/Hydraulic pumps – Electrical and hydraulics diagrams
- 9A23 – HA130/160/LS hydraulic system/Hydraulic pumps – Layout of components
- 9A24 – HA130/160/LS hydraulic system/Hydraulic pumps – Tests and diagnostics
- 9A27 – HA130/160/LS hydraulic system/Hydraulic pumps – Disassembly and reassembly
- 9A28 – HA130/160/LS hydraulic system/Hydraulic pumps – Service tools
- 9A30 – HA130/160/LS hydraulic system/Auxiliary spool valves – General
- 9A31 – HA130/160/LS hydraulic system/Auxiliary spool valves – Error codes
- 9A32 – HA130/160/LS hydraulic system/Auxiliary spool valves – Electrical and hydraulics diagrams
- 9A33 – HA130/160/LS hydraulic system/Auxiliary spool valves – Layout of components
- 9A34 – HA130/160/LS hydraulic system/Auxiliary spool valves – Tests and diagnostics
- 9A37 – HA130/160/LS hydraulic system/Auxiliary spool valves – Disassembly and reassembly
- 9A38 – HA130/160/LS hydraulic system/Auxiliary spool valves – Service tools
- 9A40 – HA130/160/LS hydraulic system/Rear linkage – General
- 9A41 – HA130/160/LS hydraulic system/Rear linkage – Error codes
- 9A42 – HA130/160/LS hydraulic system/Rear linkage – Electrical and hydraulics diagrams
- 9A43 – HA130/160/LS hydraulic system/Rear linkage – Layout of components
- 9A44 – HA130/160/LS hydraulic system/Rear linkage – Tests and diagnostics
- 9A47 – HA130/160/LS hydraulic system/Rear linkage – Disassembly and reassembly
- 9A48 – HA130/160/LS hydraulic system/Rear linkage – Service tools
- 9A50 – HA130/160/LS hydraulic system/Front linkage – General
- 9A52 – HA130/160/LS hydraulic system/Front linkage – Electrical and hydraulics diagrams
- 9A53 – HA130/160/LS hydraulic system/Front linkage – Layout of components
- 9A54 – HA130/160/LS hydraulic system/Front linkage – Tests and diagnostics
- 9A56 – HA130/160/LS hydraulic system/Front linkage – Adjustments, bleeding and calibrations
- 9A57 – HA130/160/LS hydraulic system/Front linkage – Disassembly and reassembly
- 9A58 – HA130/160/LS hydraulic system/Front linkage – Service tools
- 9B10 – GPA20/GPA40/Load Sensing – General
- 9B12 – GPA20/GPA40/Load Sensing – Electrical and hydraulics diagrams
- 9B13 – GPA20/GPA40/Load Sensing – Layout of components
- 9B14 – GPA20/GPA40/Load Sensing – Tests and diagnostics
- 9B17 – GPA20/GPA40/Load Sensing – Disassembly and reassembly
- 9B20 – GPA20/GPA40/Load Sensing/Right-hand cover plate – General
- 9B23 – GPA20/GPA40/Load Sensing/Right-hand cover plate – Layout of components
- 9B27 – GPA20/GPA40/Load Sensing/Right-hand cover plate – Disassembly and reassembly
- 6B28 – GPA20/GPA40/Load Sensing/Right-hand cover plate – Service tools
- 9B30 – GPA20/GPA40/Load Sensing/Left-hand cover plate – General
- 9B33 – GPA20/GPA40/Load Sensing/Left-hand cover plate – Layout of components
- 9B37 – GPA20/GPA40/Load Sensing/Left-hand cover plate – Disassembly and reassembly
- 9B40 – GPA20/GPA40/Load Sensing/Linkage spool valve – General
- 9B43 – GPA20/GPA40/Load Sensing/Linkage spool valve – Layout of components
- 9B47 – GPA20/GPA40/Load Sensing/Linkage spool valve – Disassembly and reassembly
- 9B50 – GPA20/GPA40/Load Sensing/Auxiliary spool valves – General
- 9B53 – GPA20/GPA40/Load Sensing/Auxiliary spool valves – Layout of components
- 9B56 – GPA20/GPA40/Load Sensing/Auxiliary spool valves – Adjustments, bleeding and calibrations
- 9B57 – GPA20/GPA40/Load Sensing/Auxiliary spool valves – Disassembly and reassembly
- 9B58 – GPA20/GPA40/Load Sensing/Auxiliary spool valves – Service tools
- 9C10 – Open Centre – General
- 9C12 – Open Centre – Electrical and hydraulics diagrams
- 9C14 – Open Centre – Tests and diagnostics
- 9C20 – Open Centre/Right-hand cover plate – General
- 9C23 – Open Centre/Right-hand cover plate – Layout of components
- 9C27 – Open Centre/Right-hand cover plate – Disassembly and reassembly
- 9C30 – Open Centre/Left-hand cover plate – General
- 9C33 – Open Centre/Left-hand cover plate – Layout of components
- 9C37 – Open Centre/Left-hand cover plate – Disassembly and reassembly
- 9D10 – 100 l/min Open Centre – General
- 9D12 – 100 l/min Open Centre – Electrical and hydraulics diagrams
- 9D14 – 100 l/min Open Centre – Tests and diagnostics
- 9D20 – 100 l/min Open Centre/Right-hand cover plate – General
- 9D23 – 100 l/min Open Centre/Right-hand cover plate – Layout of components
- 9D27 – 100 l/min Open Centre/Right-hand cover plate – Disassembly and reassembly
- 9D30 – 100 l/min Open Centre/Left-hand cover plate – General
- 9D33 – 100 l/min Open Centre/Left-hand cover plate – Layout of components
- 9D37 – 100 l/min Open Centre/Left-hand cover plate – Disassembly and reassembly
- 9E10 – Open Centre/Linkage spool valve – General
- 9E13 – Open Centre/Linkage spool valve – Layout of components
- 9E17 – Open Centre/Linkage spool valve – Disassembly and reassembly
- 9E20 – Open Centre/Auxiliary spool valves – General
- 9E23 – Open Centre/Auxiliary spool valves – Layout of components
- 9E26 – Open Centre/Auxiliary spool valves – Adjustments, bleeding and calibrations
- 9E27 – Open Centre/Auxiliary spool valves – Disassembly and reassembly
- 9E30 – Open Centre/Valve 21 bar (305 psi) – General
- 9E33 – Open Centre/Valve 21 bar (305 psi) – Layout of components
- 9E36 – Open Centre/Valve 21 bar (305 psi) – Adjustments, bleeding and calibrations
- 9E37 – Open Centre/Valve 21 bar (305 psi) – Disassembly and reassembly
-
10. Electricity
- 10A12 – Lighting and equipment – Electrical and hydraulics diagrams
- 10B10 – Fuse box – General
- 10B12 – Fuse box – Electrical and hydraulics diagrams
- 10C14 – Alternator – Tests and diagnostics
- 10C17 – Alternator – Disassembly and reassembly
- 10C18 – Alternator – Service tools
- 10E10 – Starter – General
- 10E14 – Starter – Tests and diagnostics
-
11. Electronics
-
12. Cab and Equipment
- 12A10 – Standard air conditioning – General
- 12A12 – Standard air conditioning – Electrical and hydraulics diagrams
- 12A13 – Standard air conditioning – Layout of components
- 12A14 – Standard air conditioning – Tests and diagnostics
- 12A16 – Standard air conditioning – Adjustments, bleeding and calibrations
- 12A17 – Standard air conditioning – Disassembly and reassembly
- 12B10 – Self-regulating air conditioning – General
- 12B11 – Self-regulating air conditioning – Error codes
- 12B12 – Self-regulating air conditioning – Electrical and hydraulics diagrams
- 12B13 – Self-regulating air conditioning – Layout of components
- 12B14 – Self-regulating air conditioning – Tests and diagnostics
- 12B16 – Self-regulating air conditioning – Adjustments, bleeding and calibrations
- 12B17 – Self-regulating air conditioning – Disassembly and reassembly
- 12C10 – Semi-active hydraulic suspension – General
- 12C12 – Semi-active hydraulic suspension – Electrical and hydraulics diagrams
- 12C13 – Semi-active hydraulic suspension – Layout of components
- 12C16 – Semi-active hydraulic suspension – Adjustments, bleeding and calibrations
- 12C17 – Semi-active hydraulic suspension – Disassembly and reassembly
- 13. Accessories
- 14. Service Tools
Choosing the Applicable Transmission and System References
The introduction separates specifications for the MF 7619, 7620, 7622, 7624 and 7626 by Dyna-6 and Dyna-VT configuration. The transmission chapters also distinguish ML130/ML160 hydrostatic units, GBA15 and GBA25 gearboxes, Power Shuttle, Powershift, robotic mechanical gearboxes and optional creeper or super-creeper assemblies. Match the installed drivetrain to the relevant service and calibration section.
Rear axle and PTO material is organised by HA130/160, GPA40 and GPA20 variants, including final drives, differential locks, braking, ParkLock and rear or front PTO arrangements. Hydraulic chapters further distinguish Load Sensing and Open Centre circuits; the electrical reference section provides corresponding circuit diagrams and harness information. Check the relevant diagrams and identifiers before starting a repair.
Reviews
There are no reviews yet.