Overview
The AGCO ST35X and ST40X Tractor Service Manual provides detailed technical information for compact tractor maintenance, troubleshooting, inspection, adjustment, and component repair. The workshop documentation covers engine servicing, fuel and cooling systems, clutch assemblies, mechanical transmissions, four-wheel-drive axles, rear axle components, hydrostatic steering, hydraulics, and electrical equipment.
The service documentation includes illustrated component removal and installation procedures, transmission disassembly and reassembly, mechanical shuttle servicing, PTO clutch inspection, hydraulic pump testing, three-point linkage adjustments, and electrical troubleshooting. Detailed sections address transmission input gears, synchroniser mechanisms, hydraulic control valves, differential assemblies, steering components, and electrical circuits to support accurate component servicing and repair.
Table of Contents
AGCO ST35X, ST40X Manual
- 01. Introduction
- 02. Sheet Metal and Three-Point Hitch
- Hood side panels and front grille
- Hood removal and installation
- Steering column covers
- Instrument cover and cowling
- ROPS frame and fenders
- Seat and seat suspension assembly
- Platform and floor mat servicing
- Fuel tank and muffler removal
- Drawbar and drawbar bracket
- Top link and lower lift rods
- Three-point hitch stabilisers
- 03. Major Components
- 04. Engine Service Manual
- 05. Fuel System, Cooling System and Air Cleaner
- 06. Clutch
- 07. Transmission
- Transmission general description and specifications
- Input gear construction and operation
- PTO clutch assembly
- Oil supply to transmission clutch packs
- Reducing valve operation and hydraulic piping
- PTO solenoid operation and timer control
- PTO clutch overhaul and inspection
- Clutch friction plates and brake disc inspection
- Mechanical reverse shuttle operation
- Mechanical shuttle cable and control linkage
- Forward/reverse synchroniser servicing
- Transmission input gear removal and installation
- Input shaft and idler shaft servicing
- Main transmission gear assemblies
- Transmission shift lever inspection
- Range gears and range shift linkage
- Rear differential, ring gear and pinion
- Pinion shaft disassembly and inspection
- Differential gear installation and tooth contact inspection
- Rear and mid PTO assemblies
- Front-wheel-drive shift mechanism
- 08. Front Axle (4WD)
- 09. Rear Axle and Brakes
- 10. Hydrostatic Steering
- 11. Hydraulic System
- Hydraulic system description and specifications
- Hydraulic pump removal and installation
- Hydraulic pump disassembly and overhaul
- Pump gears, O-rings and oil seals
- Hydraulic pump flow and pressure testing
- Transmission oil and filter
- Lift shaft and crank servicing
- Hydraulic cylinder and piston
- Hydraulic linkage system adjustments
- Three-point linkage main control valve
- Main spool, pilot spool and unloading valves
- Hydraulic lift neutral, raising and lowering operation
- Main control valve disassembly and reassembly
- Main relief valve servicing and pressure testing
- Three-point cylinder protection relief valve
- Slow-drop and safety check valves
- Hydraulic lift cover and piston lift rod
- Optional draft control adjustment
- Draft torsion bar and housing
- Remote hydraulic control valve servicing
- Hydraulic system troubleshooting
- 12. Electrical System
- Electrical system information and specifications
- Battery inspection and charging
- Instrument panel removal and installation
- Tachometer inspection and servicing
- Fuel gauge and fuel level sensor
- Coolant temperature gauge
- Main starter switch and combination switch
- Engine oil pressure indicator
- Power take-off electrical switch
- Electrical wiring harness
- Alternator and starter wiring connections
- Dashboard wiring harness connections
- Front lighting system
- Signal lights and tail lights
- Instrument lighting and indicator strip
- Safety switches, relays and diodes
- Electrical system troubleshooting
Transmission Input Gears and PTO Clutch Hydraulic Operation
The transmission input gear assembly incorporates a PTO clutch, reverse idler, idler gear, and forward/reverse shuttle assembly. Directional shifting is carried out through a synchroniser mechanism. Access to the input gears requires separation of the front transmission from the spacer transmission, with the workshop documentation providing the corresponding component inspection and servicing procedures.
The power take-off operates through a hydraulically actuated wet multidisc clutch pack. PTO engagement requires both the rear mechanical PTO lever and the console-mounted on/off switch to be activated. When the switch is engaged, the PTO valve is energised, allowing hydraulic pressure to clamp the clutch discs and transmit rotation to the PTO shaft. Oil is supplied from the auxiliary steering pump through a reducing valve that divides flow between primary and secondary circuits, with the secondary circuit supplying the PTO clutch pack at the regulated operating pressure.
Reviews
There are no reviews yet.