Overview
The AGCO ST35 and ST40 Tractor Service Manual provides detailed technical information for tractor maintenance, troubleshooting, inspection, adjustment, and component repair. The workshop documentation covers engine servicing, cooling and fuel systems, clutch assemblies, mechanical and Power Shuttle transmissions, front and rear axles, hydraulic steering, electrical equipment, and related tractor components.
The service documentation includes tractor separation procedures, transmission disassembly and reassembly, gear linkage adjustments, brake repairs, hydraulic pump servicing, and electrical system troubleshooting. Detailed sections address shuttle clutch mechanisms, transmission selector rails, differential assemblies, steering components, three-point linkage controls, and hydraulic pressure testing, with technical specifications and illustrated servicing instructions.
Caution: When removing the transmission shift rails, take care to prevent the detent balls from being ejected or lost. Follow the documented disassembly and reassembly procedures to maintain correct positioning of the selector mechanism components.
Table of Contents
AGCO ST35, ST40 Manual
- 01. Introduction
- General service information and indexing
- Safety precautions and tractor identification
- Standard tightening torque specifications
- Lubrication and periodic maintenance
- Technical specifications and capacities
- Gear train diagrams and travelling speeds
- Sealants, adhesives and conversion tables
- 02. Sheet Metal and Three-Point Linkage
- Hood, grille and side panel removal
- Steering column covers and instrument cowling
- ROPS frame, fenders and seat assemblies
- Platform and floor mat servicing
- Fuel tank and muffler removal
- Drawbar and drawbar bracket
- Top link, lift rods and stabilisers
- 03. Major Components
- General precautions for tractor separation
- Front axle and frame separation
- Engine removal and installation
- Engine and front transmission separation
- Front and spacer transmission separation
- Spacer transmission and differential separation
- Rear axle housing removal and installation
- Hydraulic lift cylinder cover servicing
- 04. Engine
- 05. Cooling System and Air Cleaner
- Cooling system specifications
- Radiator removal, inspection and leak testing
- Radiator hoses and fan belt
- Water pump servicing
- Thermostat inspection and replacement
- Coolant inspection and replacement
- Air cleaner servicing
- Fuel filter and fuel pump
- Fuel system air bleeding
- Cooling and fuel system troubleshooting
- 06. Clutch
- Clutch construction and specifications
- Main clutch removal and overhaul
- Clutch component inspection and reassembly
- Release bearing servicing
- Clutch shaft and related components
- Clutch rod linkage
- Clutch free-play adjustment
- Clutch troubleshooting
- 07. Transmission
- Transmission specifications and construction
- Shift patterns and power flow diagrams
- Transmission input gears
- Front transmission case servicing
- Input shaft and idler shaft
- Main transmission gears
- Transmission shift lever and linkage
- Range gears and selector mechanisms
- Rear differential, ring gear and pinion
- Rear and mid power take-off components
- Front-wheel-drive shift mechanism
- Transmission and PTO troubleshooting
- 08. Power Shuttle
- Power Shuttle operating principles
- Shuttle control lever and switches
- Shuttle valve operation
- Forward and reverse shuttle clutch
- Mechanical shuttle cables and linkage
- Forward/reverse synchroniser servicing
- Shuttle switch adjustment
- 09. Hydrostat
- 10. Front Axle (2WD)
- 11. Front Axle (4WD)
- Four-wheel-drive axle construction
- Front-wheel-drive shaft servicing
- Pivot support disassembly and reassembly
- Front differential inspection and overhaul
- Final drive assemblies
- Final drive case servicing
- Front axle end-float adjustment
- Wheel toe-in and steering stop adjustment
- Front axle troubleshooting
- 12. Rear Axle and Brakes
- Rear axle specifications and construction
- Axle shafts, bearings and seals
- Rear brake disassembly and inspection
- Brake friction plates and actuators
- Brake reassembly and adjustment
- Differential lock clutch
- Brake rods and pedals
- Parking brake servicing
- Rear axle and brake troubleshooting
- 13. Power Assist Steering
- Hydrostatic steering system
- Steering unit construction and operation
- Integral Orbitrol steering assembly
- Steering unit inspection and reassembly
- Steering cylinder
- Steering free-play adjustment
- Steering system troubleshooting
- 14. Hydraulic System
- Hydraulic system specifications
- Hydraulic pump removal and overhaul
- Hydraulic pump flow and pressure testing
- Transmission oil and filter
- Lift shaft and crank
- Hydraulic cylinder and piston
- Three-point linkage control valve
- Main relief valve and pressure checks
- Slow-drop and safety check valves
- Hydraulic linkage adjustments
- Optional draft control
- Remote control valves
- Hydraulic system troubleshooting
- 15. Electrical System
- Electrical system specifications
- Battery inspection and charging
- Instrument panel and tachometer
- Fuel gauge and coolant temperature gauge
- Starter and combination switches
- Engine oil pressure indicator
- Power take-off switch
- Electrical wiring harness
- Alternator and starter wiring
- Headlights, signal lights and instrument bulbs
- Safety switches, fuses, relays and diodes
- Electrical system troubleshooting
Transmission Shift Linkage and Selector Mechanism
The transmission service procedures describe the removal and installation of the shift linkage assembly, including the shift forks, selector rails, operating lever, cable assembly, shift cover, oil seal, arm, and gasket. The documented removal sequence involves separating the tractor between the engine and front transmission before removing the shift housing and selector rail assemblies.
During reassembly, the shift linkage components are installed in the reverse sequence, with lubrication applied to the grooves in the selector rails as specified. The related transmission sections provide information on shift lever inspection, range gear mechanisms, shuttle controls, and transmission component adjustments to support correct operation of the gear selection system.
Reviews
There are no reviews yet.