Overview
The AGCO ST45 Tractor Service Manual provides detailed technical information for compact tractor maintenance, troubleshooting, inspection, adjustment, and component repair. The workshop documentation includes four-cylinder Iseki diesel engine servicing, cooling and air cleaner systems, clutch and transmission components, four-wheel-drive front axle, rear axle and brakes, power steering, hydraulics, and electrical equipment.
The service documentation includes tractor separation procedures, engine disassembly and reassembly, transmission servicing, hydraulic pump repairs, brake adjustments, and electrical troubleshooting. Detailed sections cover sheet metal removal, three-point hitch components, PTO clutch operation, hydrostatic transmission testing, hydraulic lift controls, steering system inspection, and technical service specifications for the applicable tractor configuration.
Notice: The documentation distinguishes certain component arrangements before and effective from the “M” serial-number designation. Check the tractor identification and serial number when selecting the applicable servicing procedures.
Table of Contents
AGCO ST45 Manual
- 01. Introduction and General Information
- Manual indexing and special tools
- Repair and replacement information
- Repair time schedule references
- Workshop safety precautions
- Tractor identification and serial numbers
- Standard tightening torque specifications
- Fluid specifications and capacities
- Lubrication and periodic maintenance
- Major component identification
- Wheel and tyre specifications
- Transmission speeds
- Sealants, adhesives and metric conversions
- 02. Sheet Metal and Three-Point Hitch
- Hood side panel removal and installation
- Front grille removal and installation
- Hood removal and installation
- Steering column cover
- Instrument panel shroud
- ROPS frame removal and installation
- Fender and seat assemblies
- Seat suspension
- Floor and floor mounting components
- Muffler removal and installation
- Drawbar and drawbar bracket
- Category 1 three-point hitch specifications
- Top link and lower lift rods
- Extendable lower links and check chains
- Panel beneath the operator seat
- 03. Major Components
- General precautions for tractor separation
- Installation of standardised components
- Four-wheel-drive shaft removal and installation
- Front axle and mounting bracket removal
- Engine and front transmission separation
- Engine separation from chassis
- Front and spacer transmission separation
- Spacer and middle transmission separation
- Spacer transmission and differential separation
- Rear axle housing removal and installation
- Hydraulic cylinder cover servicing
- 04. Cooling System and Air Cleaner
- Cooling system description and specifications
- Radiator removal and installation
- Radiator inspection and leak testing
- Radiator cap inspection
- Radiator hose servicing
- Fan belt removal and installation
- Water pump removal and overhaul
- Water pump impeller and seals
- Thermostat inspection and testing
- Coolant inspection and antifreeze requirements
- Engine air cleaner servicing
- Cooling system troubleshooting
- 05. Four-Cylinder Iseki Diesel Engine
- Engine general information and specifications
- Engine service standards
- Engine inspection and troubleshooting
- Cylinder head and combustion chamber
- Valves, valve seats and valve guides
- Cylinder block, pistons and connecting rods
- Crankshaft inspection and servicing
- Intake and exhaust valve mechanisms
- Engine disassembly procedures
- Engine component reassembly
- Engine lubrication system
- Oil pump, oil filter and relief valve
- Engine coolant system
- Fuel injection pump construction and operation
- Fuel injection timing and adjustment
- Injection nozzles and nozzle holders
- Fuel injection pump disassembly and inspection
- Engine governor operation
- Alternator inspection and servicing
- Glow plugs and engine shut-off solenoid
- Engine speed pickup
- Starter removal, inspection and reassembly
- 06. Clutch
- 07. Transmission
- Transmission construction and specifications
- Wheel drive and PTO drive systems
- Transmission speed shift patterns
- Gear train diagrams
- Input gear construction and servicing
- PTO clutch and hydraulic oil supply
- Reducing valve operation
- PTO solenoid and timer control
- PTO clutch disassembly and inspection
- Transmission input housing and gears
- Hydrostatic transmission disassembly
- Hydrostatic transmission inspection and reassembly
- Hydrostatic transmission pressure testing
- Charge pressure and high-pressure relief checks
- Two-speed changeover valve
- Range transmission servicing
- Ring gear and pinion inspection
- PTO shaft and shift mechanism
- Range transmission shift linkage
- Front-wheel-drive shift mechanism
- Wheel drive and PTO troubleshooting
- 08. Front Axle (4WD)
- Four-wheel-drive front axle construction
- Front axle specifications
- Front-wheel-drive shaft servicing
- Pivot bracket bushings
- Front track and wheel alignment adjustment
- Front differential removal and installation
- Front differential overhaul and inspection
- Front wheel final drive assemblies
- Wheel shaft seals and covers
- Front axle centre section
- Front axle bracket oil seals
- Final drive housing overhaul
- Front axle troubleshooting
- 09. Rear Axle and Brakes
- Rear axle construction and specifications
- Final drive gear removal and installation
- Rear axle shafts, seals and bearings
- Brake disc servicing
- Brake system overhaul
- Brake friction plates and actuators
- Brake separator plate inspection
- Differential lock clutch servicing
- Rear axle housing replacement
- Brake adjustment
- Brake rods and pedals
- Parking brake servicing
- Rear axle assembly procedures
- Rear axle and brake troubleshooting
- 10. Power Steering System
- Power steering system construction
- Integral Orbitrol steering unit
- Steering unit component identification
- Rotor and control side disassembly
- Steering component inspection
- Control side reassembly
- Gerotor side reassembly
- Power steering troubleshooting
- 11. Hydraulic System
- Hydraulic system description and specifications
- Three-point hydraulic lift system
- Transmission oil and hydraulic filter replacement
- Hydraulic pump removal and overhaul
- Hydraulic pump inspection and repair
- Hydraulic linkage servicing
- Draft spring and housing
- Lift shaft and crank
- Hydraulic cylinder and piston
- Position and draft control adjustments
- Main hydraulic control valve
- Hydraulic control valve disassembly and reassembly
- Main piping system
- Main relief valve and pressure testing
- Cylinder protection relief valve
- Slow-return flow control valve
- Hydraulic cylinder cover and piston lift rod
- Optional remote hydraulic control
- Single-acting and double-acting hydraulic circuits
- Remote control valve servicing
- Hydraulic system troubleshooting
- 12. Electrical System
- Electrical system specifications
- Battery removal and inspection
- Instrument panel servicing
- Tachometer inspection
- Fuel gauge and fuel level sensors
- Coolant temperature gauge and sensor
- Starter and combination switches
- Lighting and turn signal switches
- Safety switches and PTO safety relay
- Power take-off switch
- Engine shutdown solenoid
- Electrical wiring harness
- Front lighting and signal lights
- Instrument panel lighting
- Glow indicator and glow plug system
- Electrical system troubleshooting
- 13. Hydraulic Schematics
Hood, Front Grille and Engine Service Access
The sheet metal servicing procedures explain how to remove the right-hand and left-hand hood side panels to access the radiator, battery, and engine components. Each panel is released using its locking lever, pulled outward at the lower edge, and lifted clear of its upper mounting points. During installation, the upper edge is correctly engaged before securing the lower locking mechanism.
The front grille can be removed to provide access for battery removal and power steering filter servicing. The procedure includes releasing the grille locks, disconnecting the headlight wiring connectors, and lifting the grille from its lower mounting hooks. Complete hood removal involves removing the side panels and grille, repositioning the fuse box, disconnecting the attached wiring, and releasing the hood mounting hardware. The documented installation procedures ensure that the exterior panels and related components are correctly refitted after servicing.
Reviews
There are no reviews yet.