Overview
The Massey Ferguson 533, 543 and 563 Tractor Workshop Service Repair Manual provides detailed technical information for maintaining, troubleshooting and repairing these Massey Ferguson agricultural tractors. The workshop documentation covers tractor servicing procedures, three-cylinder engine specifications, cooling systems, clutch assemblies, 8-speed standard and synchromesh shuttle gearboxes, rear axle components, braking systems, power take-off equipment, front axles, hydraulics and electrical systems.
Technical coverage includes dual and split-torque clutch servicing, gearbox selector mechanisms, transmission gears and shafts, transfer gearbox repairs, oil-cooled disc and drum brake systems, differential adjustment, PTO clutch overhaul, two-wheel-drive and four-wheel-drive front axle servicing, hydraulic lift adjustments, Orbitrol steering, hydraulic pressure testing and electrical troubleshooting. The manual also provides specifications, fault diagnosis references, removal and refitting procedures, component overhaul instructions and special service tool information.
Important Information: The documentation covers different transmission, clutch, brake, PTO and front axle configurations. The four-wheel-drive front axle section is specifically identified for MF 543 and MF 563 tractors. Select the workshop procedures applicable to your tractor model and installed equipment.
Table of Contents
Massey Ferguson 533, 543, 563 Tractor Service Manual
- 01. Introduction
-
02. Splitting the Tractor
- Splitting the Tractor Between the Front Axle and Engine – 3-Cylinder
- Splitting the Tractor Between the Engine and Gearbox – 3-Cylinder
- Splitting the Tractor Between the Gearbox and Spacer or Centre Housing – 3-Cylinder
-
03. Engine
- Engine Specifications
- Massey Ferguson 533, 543 and 563 Tractor Engine
- Recommended Engine Bolt Tightening Torques
- Cooling System
- Cooling System Specifications
- Cooling System Fault Diagnosis
- Frost Precautions
- Cooling System General Description
- Radiator – 3-Cylinder Tractor
- Fan Belt
- 1100 Series Non-Electronic Engine Drop Sheet
-
04. Clutch
- Clutch Specifications
- Dual Clutch – General Description
- 305 mm Split-Torque Clutch – General Description
- Clutch Fault Finding
- PTO Clutch
- Clutch Release Bearing
- Clutch Release Mechanism
- Dual Clutch Assembly – Removal and Refitting
- Dual Clutch Assembly – Overhaul
- Split-Torque Clutch Assembly
- Split-Torque Clutch Servicing
- Flywheel Pilot Bearing
-
05. Gearbox
- 8-Speed Standard Gearbox
- 8-Speed Standard Gearbox – Specifications
- 8-Speed Standard Gearbox – General Description
- Gear Shift Levers
- Selector Rails and Forks
- Normal and Heavy-Duty Epicyclic Units
- Normal-Duty Epicyclic Unit
- Heavy-Duty Epicyclic Unit
- Input Shafts and Housing
- PTO Drive Shaft Front Bearing
- Layshaft, Mainshaft, PTO Shaft and Gears
- 8-Speed Synchromesh Shuttle Gearbox
- 8-Speed Synchromesh Shuttle Gearbox – Specifications
- 8-Speed Synchromesh Shuttle Gearbox – General Description
- Synchromesh Gear Shift Levers
- Forward/Reverse Shuttle Control Lever
- Selector Rails and Fork
- Normal-Duty Epicyclic Unit – Removal and Refitting
- Normal-Duty Epicyclic Unit – Overhaul
- Synchromesh Input Shafts and Housing
- PTO Drive Shaft Front Bearing
- Layshaft, Mainshaft, PTO Shaft and Gears
- Transfer Gearbox and Drive Shaft
- Transfer Gears – MF 543 and MF 563
- Drive Shaft – Removal and Refitting
- Drive Shaft – Overhaul
- Transfer Gears
- Transfer Gearbox
- Transfer Box
-
06. Rear Axle and Brakes
- Brake System Specifications
- Multi-Disc Oil-Cooled Brakes
- Double-Acting Drum Brakes
- Brake System General Description
- Drum Brake Adjustment
- Disc Brake Adjustment
- Drum Brakes – Removal and Refitting
- Brake Shoe Relining and Overhaul
- Drum Brake Overhaul
- Disc Brake Actuator Housing Overhaul
- Disc Brake Overhaul
- Footbrake Linkage and Pedals
- Footbrake Pedal Adjustment
- Cable-Operated Parking Brake
- Crownwheel, Pinion and Differential Lock
- Crownwheel and Pinion Specifications
- Differential Lock – Drum Brake Adjustment
- Differential Lock – Disc Brake Adjustment
- Differential Lock – Drum Brake Overhaul
- Differential Lock – Disc Brake Overhaul
- Lower Link Pin – Drum Brakes
- Differential Lock Coupler Cap
- Differential Unit Overhaul
- Crownwheel and Pinion Overhaul
- Differential Preload Check
- Rear Axle Specifications
- Indirect-Drive Rear Axle
- Direct-Drive Rear Axle
- Rear Wheel Stud – Removal and Refitting
- Epicyclic Unit Ring Gear
- Epicyclic Planet Gears and Sun Gear
- Epicyclic Unit Overhaul
- Trumpet Housing and Carrier Plate
- Axle Shaft – Direct Drive with Drum Brakes
- Direct-Drive Trumpet Housing
- Drawbar and Linkage
- Drawbar and Linkage Specifications
- Left-Hand Lift Rod
- Right-Hand Lift Rod and Levelling Box
- Levelling Box Overhaul
- Swinging Drawbar – Removal and Refitting
-
07. Power Take-Off (PTO)
- Single-Speed Power Take-Off
- Single-Speed PTO Specifications
- Single-Speed PTO – General Description
- PTO Shaft, Oil Seal and Bearing Overhaul
- PTO Shaft, Bearing and Oil Seal – Removal and Refitting
- Ground Speed Gears and Bearings
- Left-Hand PTO Side Cover – Removal and Refitting
- Left-Hand PTO Side Cover – Overhaul
- Independent PTO (IPTO) – Single-Speed Power Take-Off
- Independent PTO Specifications
- Independent PTO – General Description
- Independent PTO Fault Diagnosis
- Independent PTO Left-Hand Side Cover
- Independent PTO Side Cover Overhaul
- PTO Clutch Unit – Removal and Refitting
- PTO Clutch Unit Overhaul
-
08. Front Axle
- 2WD Front Axle – 3-Cylinder Tractors
- 2WD Front Axle Specifications
- 2WD Front Axle – General Description
- Front Wheel Toe-In Adjustment
- Front Hub Adjustment
- Front Hub Overhaul
- Spindle Shaft – Removal and Refitting
- Spindle Housing – Removal and Refitting
- Spindle Housing Overhaul
- Axle Beam Assembly – Removal and Refitting
- Front Axle Support Overhaul
- 4WD Front Axle – MF 543 and MF 563
- 4WD Front Axle Specifications
- 4WD Front Axle – General Description
- Wheel Alignment and Steering Adjustment
- Track Rod and Ball Joint
- Front Axle – Removal and Refitting
- Planetary Carrier – Removal and Refitting
- Hub Oil Seal – Removal and Refitting
- Planetary Carrier and Hub Overhaul
- Swivel Housing and Pins
- Drive Shaft and Oil Seals
- Drive Shaft Overhaul
- Pinion Oil Seal – Removal and Refitting
- Differential Assembly – Removal and Refitting
- Differential Assembly Overhaul
- Crownwheel and Pinion Overhaul
- Steering Ram – Removal and Refitting
- Steering Ram Overhaul
-
09. Hydraulics and Steering
- Lift Hydraulics
- Hydraulic Lift Specifications
- Hydraulic Lift – General Description
- Control Spring Assembly – Removal and Refitting
- Control Spring Assembly Overhaul
- Hydraulic Lift Cover Overhaul
- Hydraulic Lift Cylinder Overhaul
- Quadrant and Support Assembly Overhaul
- Hydraulic Static Adjustments
- Hydraulic External Adjustments
- Hydraulic Pressure Test
- Hydraulic Lift Pump – Removal and Refitting
- Hydraulic Lift Pump Overhaul
- Hydraulic Relief Valve Adjustment
- Orbitrol Steering Unit
- Orbitrol Steering Specifications
- Orbitrol Steering – General Description
- Steering System Pressure Test
- Orbitrol Steering Unit – Removal and Refitting
- Orbitrol Steering Unit Overhaul
- Steering System Pressure Test – 3-Cylinder Tractors
- Steering System Flow Test
- Pressure-Maintaining Valve Pressure Test
- Independent PTO Pressure Test
- Auxiliary Circuit Flow Test
- Auxiliary Hydraulics
- Auxiliary Hydraulics Specifications
- Auxiliary Hydraulics – General Description
- Pressure-Maintaining Valve
- Hydraulic Spool Valves
- Auxiliary Hydraulic Lift Pump – Removal and Refitting
- Auxiliary Hydraulic Pump Overhaul
-
10. Electrical Equipment
- Electrical System – General Information
- Electrical System Specifications
- Electrical Fault Diagnosis
- Headlight Beam Adjustment
- Headlight Bulbs
- Instrument Panel Light Bulbs
- Rear Work Light Bulb
- Warning Light Bulb
- Rear Red Light Bulb
- Instrument Panel Flasher Unit
- Fuses
- Electrical System – Battery
- Battery Specifications
- Battery General Description
- Battery Routine Maintenance
- Battery Removal and Refitting
- Electrical System – Starter Motor
- Starter Motor Specifications
- Starter Motor – General Description
- Neutral Start Switch – Removal and Refitting
- PTO Neutral Start Switch – Removal and Refitting
- Starter Motor – Removal and Refitting
- Electrical System – Alternator
- Alternator Specifications
- Alternator – General Description
- Alternator Belt Tension Adjustment
- Alternator – Removal and Refitting
- Electrical Wiring Diagrams
- Instrument Panel Wiring Diagrams
-
11. Service Tools
Transmission, PTO and Hydraulic Repair Information
The Massey Ferguson 533, 543 and 563 workshop manual includes technical procedures for servicing standard and synchromesh shuttle gearboxes, dual and split-torque clutches, rear axle differential assemblies, PTO components, front axle systems and hydraulic lift equipment. Its specifications, adjustment instructions, fault diagnosis sections and component overhaul references support workshop maintenance and repairs on the applicable tractor configuration.
Reviews
There are no reviews yet.