Overview
The AGCO ST22A Compact Tractor Service Manual provides detailed technical information for tractor maintenance, troubleshooting, inspection, adjustment, and component repair. The workshop documentation covers engine servicing, chassis components, hydrostatic transmission systems, rear and front axles, hydraulic steering, electrical equipment, and mower deck maintenance.
The service documentation includes component removal and installation procedures, transmission disassembly and reassembly, PTO clutch servicing, brake adjustments, hydraulic system inspection, and electrical troubleshooting. Detailed sections address tractor identification, lubrication schedules, hydrostatic drive controls, hydraulic lift cylinders, steering components, and mower deck servicing, supported by technical specifications and maintenance procedures.
Table of Contents
AGCO ST22A Manual
- 01. Introduction and General Information
- Manual indexing and special tools
- Repair and replacement procedures
- Repair time schedule references and amendments
- Workshop safety precautions
- Tractor model identification and serial numbers
- Chassis and engine identification
- General tractor specifications
- Agricultural tyre drive system shaft revolutions
- Agricultural tyre PTO and gear pump drive information
- Turf tyre drive system shaft revolutions
- Turf tyre PTO and gear pump drive information
- Lubrication and periodic maintenance
- Fluid specifications and capacities
- Engine oil, coolant and fuel tank
- Transmission and differential housing lubrication
- Four-wheel-drive front axle lubrication
- Grease fittings and lubrication points
- Periodic maintenance schedule
- Standard tightening torque specifications
- Sealants, adhesives and conversion tables
- 02. Chassis
- ROPS frame removal and assembly
- Platform and sheet metal servicing
- Fuel tank removal and installation
- Front axle removal and reassembly
- Transmission removal and reinstallation
- Engine removal and reassembly
- 03. Engine
- 04. Cooling, Air and Fuel Systems
- Engine service access
- Engine oil filter access
- Cooling system
- Thermostat
- Engine air cleaner
- Fuel system
- Fuel filter servicing
- Fuel pump
- Fuel system air bleeding
- Fuel tank filler cap
- Throttle lever
- 05. Transmission
- Ground speed selection
- Hydrostatic transmission
- Hydrostatic transmission major components
- HST operating diagram
- Hydrostatic pedal linkage
- Hydro pedal linkage reassembly
- Transmission disassembly
- Transmission component inspection
- Transmission reassembly
- Power take-off system
- PTO clutch disassembly
- Rear PTO disassembly and reassembly
- Transmission shift linkage
- Transmission assembly procedures
- 06. Rear Axle and Brakes
- Rear axle and brake component inspection
- Brake friction plates
- Brake actuator assembly
- Brake separator plates
- Brake component reassembly
- Brake adjustment
- 07. Front Axle
- Front axle assembly
- Front axle reassembly
- Front axle oil
- 08. Hydraulic System
- Hydraulic system specifications
- Hydraulic component locations and test ports
- Hydraulic control valve
- Control valve components and assembly
- Control valve hydraulic circuit
- Hydraulic control valve linkage
- Hydraulic lift cylinder assembly
- Lift cylinder inspection and reassembly
- Hydraulic steering system
- Steering wheel and Orbitrol steering unit
- Steering component removal and inspection
- Steering unit reassembly
- Steering cylinder servicing
- Steering free-play adjustment
- 09. Electrical System
- Electrical wiring harness
- Battery and electrical system
- Engine starting switches
- Wiring and fuse arrangements
- Safety switches, fuses and relays
- Electrical fuel shut-off solenoid
- Engine oil pressure sending unit
- Water temperature sending unit
- Fuel gauge sending unit
- 10. Mower Deck
- Mower deck general information
- Safety and cutting height adjustment labels
- Mower deck major components
- Mower deck installation
- Mower deck linkage adjustment
- Mower deck removal
- Mower deck lubrication and maintenance
- Mower deck lubrication chart
- V-belt inspection and replacement
- Mower blade removal and installation
- Mower blade shimming and wear inspection
- Gauge wheel inspection
- Mower deck roller inspection
- Belt cover cleaning
- Mower deck gearbox
- Gearbox oil replacement
- Gearbox disassembly and reassembly
- Gearbox backlash adjustment
- Mower deck spindles
Drivetrain Configurations and Mower Deck Servicing
The general information section provides separate shaft revolution references for agricultural and turf tyre configurations, covering the drive system, power take-off, and gear pump system. These references help distinguish the documented drivetrain arrangements when consulting transmission specifications and related servicing information.
The mower deck documentation provides procedures for deck installation, removal, linkage adjustment, and periodic maintenance. Additional servicing information covers V-belt replacement, blade inspection and shimming, gauge wheels, rollers, gearbox lubrication, backlash adjustment, and spindle components. These sections support inspection and maintenance of the applicable mower deck assembly.
Reviews
There are no reviews yet.