Overview
The AGCO ST25 Compact Tractor Service Manual provides detailed technical information for tractor maintenance, troubleshooting, inspection, adjustment, and component repair. The workshop documentation covers engine servicing, clutch assemblies, mechanical and hydrostatic transmissions, front and rear axles, braking systems, hydraulic steering, electrical equipment, and periodic maintenance.
The service documentation includes component disassembly and reassembly procedures, transmission servicing, clutch inspection, hydraulic pressure testing, brake adjustments, and electrical troubleshooting. Detailed sections address hydrostatic transmission components, PTO clutch assemblies, differential mechanisms, hydraulic control valves, steering systems, and fastening specifications to support accurate component servicing and repair.
Notice: The supplied workshop reference is identified as effective from the “L” serial-number designation. Confirm the tractor serial number and applicable transmission configuration before selecting servicing procedures.
Caution: Special bolts are used in specific locations and must not be interchanged with standard fasteners. Tighten bolts and nuts to their specified torque values and follow the documented requirements for locking wire, tab washers, adhesives, and sealants to maintain correct assembly and prevent oil leakage.
Table of Contents
AGCO ST25 Manual
- 01. General Information
- Tractor identification and serial numbers
- General tractor specifications
- Precautions for disassembly and reinstallation
- Installation of standardised components
- Standard tightening torque specifications
- Sealants and adhesives
- Conversion tables
- 02. Engine
- 03. Major Components
- 04. Clutch System
- Clutch construction and operating components
- Clutch disassembly
- Clutch disc inspection
- Clutch cover assembly inspection
- Release bearing inspection
- Clutch reassembly precautions
- Clutch housing plug
- Clutch troubleshooting
- 05. Transmission
- Gear-type transmission
- Gearbox disassembly and inspection
- Transmission reassembly precautions
- Hydrostatic transmission power train diagram
- Transmission component disassembly and reassembly
- PTO clutch for hydrostatic transmission
- PTO clutch for standard transmission
- Clutch construction and inspection
- Mid PTO construction and servicing
- 06. Hydrostatic Transmission
- Hydrostatic transmission construction
- Variable displacement hydraulic pump
- Fixed displacement hydraulic motor
- Hydrostatic transmission control valves
- Low-pressure relief and suction check valves
- High-pressure relief valve
- Neutral valve and check valve
- Hydrostatic transmission troubleshooting
- Hydrostatic unit disassembly
- Pump and motor cylinder block servicing
- Pump shaft, motor shaft and trunnion shaft
- Port block and valve plate servicing
- Criteria for replacing worn components
- Hydrostatic unit reassembly
- HST control pedal removal and installation
- Hydrostatic cruise control servicing
- 07. Rear Axle and Brakes
- Rear axle construction and operation
- Rear axle disassembly and inspection
- Rear axle reassembly and adjustment
- Brake system construction
- Brake disassembly and inspection
- Brake reassembly precautions
- Brake adjustment for mechanical transmission
- Rear axle and brake troubleshooting
- 08. Front Axle
- 09. Hydraulic System
- Hydraulic system circuit diagrams
- Hydraulic piping and specifications
- Hydraulic system disassembly and reassembly
- Main hydraulic control valve
- Control valve inspection and servicing
- Hydraulic safety and relief valves
- Flow divider and PTO clutch valve
- Flow control valve inspection and adjustment
- PTO solenoid valve
- Hydraulic pump disassembly and overhaul
- Hydraulic pump inspection and repair
- Pump gears, O-rings and oil seals
- Transmission oil and filter servicing
- Hydrostatic oil filter replacement
- Hydraulic system troubleshooting
- 10. Electrical Accessories
- Battery and electrical system
- Neutral starting switches
- Wiring and fuse arrangements
- Instrument panel components
- Electrical fuel shut-off
- Main electrical switch
- Indicator lights and tachometer
- Fuel level indicator sending unit
- Electrical system troubleshooting
- 11. Steering System
- Hydrostatic steering construction
- Major steering components
- Integral Orbitrol steering unit
- Steering component inspection
- Steering unit reassembly
- Flow control valve assembly
- Steering cylinder system
- Steering system troubleshooting
- 12. Lubrication and Periodic Maintenance
Transmission Configurations and PTO Clutch Servicing
The workshop documentation distinguishes between gear-type and hydrostatic transmission arrangements, providing separate information for the applicable transmission components. The standard transmission section includes gearbox inspection and PTO clutch construction, while the hydrostatic transmission section covers hydraulic pump and motor operation, control valves, disassembly, reassembly, and replacement criteria for worn components.
The power take-off servicing information includes clutch assemblies for both standard and hydrostatic transmission configurations. Separate procedures describe PTO clutch inspection and reassembly, along with the construction and servicing of the mid PTO. Technicians can use the relevant transmission and hydraulic sections to identify the correct components and procedures for the equipment configuration being serviced.
Reviews
There are no reviews yet.