Overview
The Massey Ferguson 9812 Planter Workshop Service Manual provides technical guidance for setting up, maintaining, diagnosing and repairing the planter and its mechanical, pneumatic, hydraulic and electronic systems. The workshop index covers row-unit gauge wheels and openers, seed meters, ground-drive and hydraulic-drive transmissions, central-fill air delivery, hydraulic pumps and cylinders, frame assemblies, fertilizer equipment and planter monitoring controls.
Detailed sections address row-unit bearing and seal replacement, drive chain and sprocket servicing, blower inspection and reassembly, lift and fold hydraulic schematics, marker and lift cylinder repairs, and fertilizer piston pump overhaul. The documentation also includes field adjustment references, seeding-rate charts, ISOBUS and GTA console setup, diagnostics, calibration, alarms and software procedures, with separate references for configuration-dependent equipment.
Notice: The source includes configurations and optional equipment such as ground or hydraulic drive, central fill, fertilizer systems, markers, and 16-row or 24-row references. These references do not mean every listed component is fitted to each 9812 planter. Use the sections that match the machine’s actual arrangement.
Safety: The manual includes specific safety information for planter operation, transport, agricultural chemicals and servicing. Review the corresponding safety instructions before operating, adjusting or repairing the equipment.
Table of Contents
Massey Ferguson 9812 Manual
- 01. General Information, Safety and Field Operations
- Planter identification and serial number plate location
- Safety symbols, messages and safety signs
- Operating, transport and servicing safety precautions
- Agricultural chemical handling precautions
- General planter, frame, tyre and wheel specifications
- Row unit, air system and hydraulic specifications
- Shear pins, electronic seed drive controller and fuse references
- Approximate planter shipping weights
- Tractor horsepower and wheel tread requirements
- Tractor PTO, hydraulic and electrical requirements
- Tractor and planter preparation
- Pneumatic down pressure and swath control requirements
- Planter lubrication, bolt torque and tyre inflation
- Optional marker, chain and seed disc preparation
- Connecting and disconnecting the three-point hitch
- PTO hydraulic pump coupling, bracket and fluid connections
- Planter hitch height adjustment
- Frame fold control box and frame control system
- Planter folding, unfolding and transport preparation
- Daylight and nighttime lighting operation
- Field setup, field operation and completion checks
- Optional marker operation, sequence valve and position switch
- Optional marker shear bolts
- Seed meter operation and seed recommendations
- Central-fill hopper, seed removal and air pressure
- Standard-duty and heavy-duty down-pressure springs
- Pneumatic down-pressure compressor operation
- Closing wheel setup and row-unit-mounted tillage options
- Frame-mounted coulters, residue managers and disc types
- ISOBUS planter system reference
- Liquid fertilizer and single-/double-disc opener references
- Air pressure gauge calibration and initial pressure settings
- Seed disc installation, seed gate and tickler brush
- Ground-drive seed rate transmission and planting-rate charts
- Seed disc identification and seed population charts
- Gauge wheel depth setting and closing wheel adjustment
- Liquid fertilizer piston pump drive and application-rate charts
- Hydraulic circuit priming and frame control box
- Radar sensor, test switch and frame height/lift switches
- Standard and metric bolt torque tables
- Installation instructions
- 02. Row Unit Service and Components
- Gauge wheel components and tyre-to-opener disc clearance
- Gauge wheel arm, seal and bearing replacement
- Gauge wheel bushings, bearing rod and mounting
- Gauge wheel disassembly, inspection and reassembly
- Opener disc blade replacement and adjustment
- Opener disc bearing replacement
- Scrapers, seed tubes and tube guards
- Seed tube sensor cleaning
- Row unit lower assembly and depth gauge service
- Depth gauge removal, disassembly, reassembly and installation
- Single closing wheel removal and rebuilding
- Dual rubber and cast closing wheel components and service
- Row unit linkage removal, installation and maintenance
- Pneumatic down-pressure air compressor specifications and replacement
- Air compressor air filter
- Air spring removal and installation
- Row unit drive chains and sprockets
- Seed meter drive, optional chain guard and roller chain
- Idler pulley and sprocket assembly servicing
- Seed meter removal and installation
- Seed meter clutch alignment
- Metering unit drive shaft and bearing service
- 03. Drive Transmission
- Roller chain lubrication and elongation checks
- Sprocket wear and alignment
- Ground-drive wheel arm operation
- Ground-drive roller chain removal and installation
- Front sprocket assembly disassembly and reassembly
- Upper wheel arm tightener and torsion spring
- Lower rear sprocket cluster and rear shaft assembly
- High/low idler position change
- Ground-drive wheel and tyre assembly servicing
- Ground-drive idler sprocket and idler pulley service
- Hydraulic-drive operation and roller chain service
- Hydraulic-drive 16-tooth sprocket replacement
- Hydraulic-drive idler pulley service
- Hydraulic-drive 40-tooth sprocket removal and installation
- 04. Central Fill and Seed Meter Air Systems
- Central-fill air pressure and blower system
- Central-fill blower removal, disassembly and inspection
- Central-fill blower reassembly and installation
- New or repaired blower startup
- Plenum operation and cleaning
- Central-fill plenum seed delivery routing
- Seed delivery diagrams for 16-row left and right wings
- Seed delivery diagrams for 24-row left and right wings
- Central seed delivery diagrams for 16- and 24-row layouts
- Seed meter air pressure
- Seed meter air pressure gauge calibration and replacement
- Seed meter blower removal and disassembly
- Seed meter blower inspection, assembly and installation
- 05. Hydraulics, Motors and Cylinders
- Planter lift and fold hydraulic schematic
- Ground drive without central fill — tractor remote connections
- Ground drive with central fill — tractor remote connections
- Hydraulic drive with central fill — PTO pump arrangement
- Hydraulic drive with central fill — tractor remote arrangement
- Hydraulic drive without central fill — tractor remote arrangement
- PTO hydraulic pump specifications and operation
- PTO pump removal, disassembly, inspection and reassembly
- PTO pump installation
- Row unit hydraulic drive motor specifications and repair
- Central-fill blower hydraulic motor specifications and repair
- Central-fill blower motor test run
- Seed meter blower hydraulic motor servicing
- Hydraulic oil cooler inspection, cleaning and replacement
- Fold cylinder specifications and operation
- Fold cylinder removal, inspection and rebuilding
- Marker cylinders — 8816 and 8824 references
- Marker cylinder disassembly, inspection and installation
- Lift cylinder components and operating principles
- Master, slave and lift-assist cylinder specifications
- Wing and middle lift cylinder removal and installation
- Lift cylinder disassembly, inspection and reassembly
- 06. Electrical
- 07. Frame, Wings and Markers
- Lift wheels and tyres — removal, inspection and rebuilding
- Lift wheel arm removal and installation
- Wing brace removal and installation
- Inner wing mounting removal and installation
- Outer wing mounting removal and installation
- Lower marker arm removal — 16-row and 24-row references
- Lower marker arm installation — 16-row and 24-row references
- Marker arm length adjustment
- Upper marker arm removal and installation
- Telescoping rod roller link
- Marker gauge wheel removal — 16-row and 24-row references
- Marker gauge wheel disassembly and reassembly
- Marker gauge wheel installation
- Marker disc blade removal and replacement
- Marker disc blade adjustment
- 08. Troubleshooting
- 09. Fertilizer System
- Single-piston fertilizer pump — NGP-6055
- Fertilizer piston pump removal, disassembly and inspection
- Fertilizer pump check valves and piston inspection
- Rod packing and crankcase components
- Fertilizer piston pump reassembly and installation
- Double-piston fertilizer pump — NGP-8055-DR
- Fertilizer drive operation
- Fertilizer drive roller chains and drive wheel service
- Fertilizer ball valve operation and service
- 2-inch short ball valve removal and installation
- 1.5-inch ball valve and strainer service
- 2-inch full-port ball valve removal and installation
- Double-disc fertilizer opener service
- Single-disc fertilizer opener service
- Fertilizer disc opener mounting — 16-row references
- Fertilizer disc opener mounting — 24-row references
- 10. Consoles, ISOBUS and Seed Monitoring
- GTA Console I and GTA Console II schematics
- ISOBUS planter system and operating performance
- Console screen, data labels, symbols and bar graphs
- Console work screen, key functions and diagnostics
- Seed monitoring, material selection and ground speed
- Alarm screens, accumulators and module configuration
- Import and export of console configurations
- Hydraulic-drive planter setup and seed-specific settings
- Ground-drive planter setup and seed-specific settings
- Hydraulic-drive operation, master switch and planting controls
- Hydraulic-drive seeding rate changes and application maps
- Ground-drive monitoring and planting operation
- System powered-on time, active time and distance accumulators
- Material setup and channel setup order
- Hydraulic-drive and ground-drive material settings
- Preset material selection
- Hydraulic-drive channel calibration
- GPS implement setup
- Seed monitor setup and row population monitoring
- Population alarms, row failure rate and population filtering
- Row widths, row status and implement width
- Ground speed sources and calibration
- Ground speed constants, shut-off speed and overrides
- Module addresses and automatic configuration
- Bridge and hopper sensor setup
- Accessory sensors and alarm settings
- Work screen configuration and display data items
- Population, singulation, spacing and area displays
- Channel rate, RPM and product level displays
- Diagnostic screen and hydraulic valve position diagnostics
- Bridge diagnostics and seed count
- Remote test switch, continuous test and five-revolution test
- Alarm history, alarm details and alarm chart
- GTA Console I and II dual hydraulic-drive startup guides
- GTA Console I software upgrade
- GTA Console II software upgrade
Selecting the Correct Planter Drive and Seed Delivery References
The hydraulic schematics distinguish tractor-remote and PTO-pump arrangements, with additional differences for machines equipped with central fill. The air-system section also separates the central-fill blower and plenum from the seed meter blower. Identify these connections and assemblies before selecting the associated test, removal or reassembly instructions.
Row-unit, marker and fertilizer references include 16-row and 24-row layouts, and some marker cylinder information is identified by 8816 or 8824 designation. The GTA console chapters provide different setup and operating paths for ground-drive and hydraulic-drive planters. Match the actual row layout, drive type and monitoring equipment to the relevant instructions.
Reviews
There are no reviews yet.